收藏本站
Automatic RF MESFET Amplifier
Drain-Current Controllers
VOLTAGE OR
TEMPERATURE
MEASUREMENT VALUE
HIGH
THRESHOLD
REGISTER
LOW
THRESHOLD
REGISTER
ALARM
COMPARATOR
(ACTIVE-LOW)
ALARM INTERRUPT
(ACTIVE-LOW)
READ ALARM
FLAG REGISTER
Figure 27. ALARM Hysteresis-Mode Timing Example
READ ALARM
FLAG REGISTER
TIME
ALARM threshold register value. See Figure 26. If an
ADC output value exceeds its respective ALARM high
threshold register value, the ALARM output triggers. The
ALARM condition remains in place until the measured
value falls below the low threshold value. Figure 27
details a hysteresis-mode timing example.
When operating in interrupt mode, the ALARM output
triggers when the measured ADC output value exceeds
either the high or low threshold. However, in interrupt
mode, the ALARM output remains active until reading
the ALARM flag register. Reading the ALARM flag reg-
ister resets the flag bits and the ALARM output.
The default values for the high and low threshold regis-
ters are the extremes of the measured range (all 1s or
all 0s, respectively). The ALARM output can be config-
ured to be open-drain or push-pull and active-high or
active-low through the hardware ALARM configuration
register. See Table 12. At power-up, the ALARM output
is configured as an active-high output that operates in
interrupt mode.
Automatic GATE Clamping
Configure the ALARM output to clamp the GATE1 out-
put to ACLAMP1 or GATE2 output to ACLAMP2 in
response to an ALARM condition through the hardware
ALARM configuration register. See Table 12c. Set the
ALM_CLMP_ bits, D5 –D2, to clamp the respective
channel’s GATE output.
Each channel has four possible ALM_CLMP1/
ALM_CLMP0 values:
? ALM_CLMP1/ALM_CLMP0 = 00
Power-on reset state. GATE_ clamps through a
series 2.4k Ω resistor to the ACLAMP_, regardless
of any ALARM condition. Reset these 2 bits before
attempting to change the DAC voltage.
? ALM_CLMP1/ALM_CLMP0 = 01
The automatic GATE_ clamp is disabled in this mode.
The GATE_ outputs are not affected by any ALARM
conditions. The ALARM output function operates nor-
mally (samples beyond their thresholds still cause
ALARM flags to be set and ALARM behaves accord-
ing to the comparator/interrupt mode).
? ALM_CLMP1/ALM_CLMP0 = 10
This mode provides fully automatic clamping. Prior to
an ALARM condition, the GATE_ voltage is controlled
by the sense voltage (MAX11014) or the DAC setting
(MAX11015). When an ALARM condition triggers, the
GATE_ voltage clamps to ACLAMP_. The clamp is
applied as long as the ALARM condition is valid. The
GATE_ clamp is released when a subsequent ADC
conversion clears the ALARM condition. The GATE_
voltage is then restored to the sense voltage/DAC set-
ting. Configure the ALARM output in comparator
mode to assert when the GATE_ clamp is active.
______________________________________________________________________________________
57
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX12000ETB+T IC AMP GPS FRONT 1575MHZ 10TDFN
MAX12005ETM+T IC SATELLITE IF SWITCH 48-TQFN
MAX1385BUTM+ IC RF LDMOS BIAS CNTRLR 48-TQFN
MAX1470EUI+T IC RECEIVER 315MHZ 28-TSSOP
MAX1470EVKIT-315 EVAL KIT FOR MAX1470 315MHZ
MAX1471EVKIT-315 EVAL KIT FOR MAX1471 315MHZ
MAX1472EVKIT-433# EVAL KIT MAX1472
MAX1473EVKIT-433 EVAL KIT MAX1473
相关代理商/技术参数
MAX11014EVKIT+ 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX11014 - Bulk
MAX11015 功能描述:射频放大器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel
MAX11015BGTM 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11015BGTM+ 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11017 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX11017ATL+ 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX11017ETL+ 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX11019 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32